Now for some pics! This is to help make wrapping your bowtie easier.
It should take the shape a rectangle. So far, so good right? Fold your tie to the right once, then back to the left. Don't worry if your tie sticks out on the sides a little. It will be concealed in the next steps. Fold the tail back to the right until you reach the middle of the rectangle. This is to help make wrapping your bowtie easier.
Now for some pics! Pick up your Bowtie and turn it to the front. Turn the tail of the tie to where the inside if the tail is facing you. It may feel a little weird in the back but don't worry, it's normal. Wrap the tail of the tie up the middle of the Bowtie and around to the back. The back of the Bowtie may look a little busy but no one will see that part. It will all come together, trust me.
Sew the remaining short edge of the tie. On the remaining open end of the tie, flip the raw edges inward by about 0. This will secure the open end of the bow tie.
If desired, you may also sew a straight stitch across the other short end of the tie so that the ends of the tie match each other. Iron your bow tie. Ironing will make the tie look neat and crisp after it is tied. Place the bow tie on a flat surface, such as an ironing board or over a towel on a table or counter.
Then, run the heated iron over the fabric to flatten it out, especially along the seams. Make sure that the tie is free of bumps, creases, and wrinkles when you are finished. If your tie is made from a delicate fabric, then you may want to place a t-shirt or thin towel over the tie before you iron it. Place your iron on its lowest setting as well. Try on the bow tie. After you finish ironing the bow tie, tie it around your neck to try it on.
A scrap of fabric from the remnants bin at your local fabric store should provide plenty of fabric. Cotton works best, but you can use any lightweight fabric you want. Use your ruler to measure the fabric and mark where you need to cut it with a piece of chalk.
Then, cut along the chalk lines to get the 2 pieces. Fold the square piece in half with the wrong sides facing out. Then, add a line of hot glue along the raw edge on the right print side of the fabric. Press the edges together to create a seam. Be careful not to touch the hot glue with your bare fingers.
You may want to wear gloves or use the ruler to press down on the edges of the fabric. Invert the tube of fabric so that the right sides are exposed. Once the glue is cool and the edges are secured, turn the tube of fabric so that the right sides are facing out and the raw edges of the seam are hidden. Then, flatten the tube and position the glued seam so that it is in the center of 1 side of the rectangle, not on the edge. Fold the ends in by 0. Make sure that the ends are even.
Then, add a line of hot glue along the fold on the inside of the tube. Press the edges together using your gloved fingers or a ruler. This may help to keep the tube flat.
Fold the small strip so the edges overlap and secure them with glue. Lay the small strip so that the right side is facing down and apply a line of hot glue down the center of the strip. Then, fold 1 of the long sides over to the center of the strip and apply another line of hot glue over the edge of the strip.
Fold the other side over that 1 and press it down to secure it. This may help to keep it flat. Pinch and fold the middle of the fabric into the shape of an accordion. Loosen your grip on the center slightly to expose the area between the folds. Then, apply a few dabs of hot glue to the areas between the folds and press the folds back together.
Repeat this on both sides of the bow to secure the folds in the center. Wrap the smaller fabric piece around the center of the bow. Take the strip of fabric and wrap it around the center of the bow. Then, apply a few drops of hot glue to the back of the bow and wrap 1 end of the fabric strip over it.
Then apply another dab of glue onto the strip at the back of the bow, and press the other end into the glue. Attach a clip to the back of the bow tie using hot glue. Add a line of glue onto the back of the clip and press it onto the back of the bow tie. Hold them together tightly for a minute to allow the glue to cool and bond with the fabric and clip. Avoid using a safety pin to attach the bow as this may poke the baby if it comes undone.
The baby may also try to put it into their mouth and this could result in injury. Not Helpful 1 Helpful 2. Include your email address to get a message when this question is answered. Already answered Not a question Bad question Other. By using this service, some information may be shared with YouTube.
Quick Summary To sew your own bow tie, begin by picking out the fabric you want, then find a pattern from a craft store or download one from the internet. Did this summary help you? Warnings Be careful when using a hot glue gun! Do not get any hot glue on your skin or it will burn you.
Strangulation may occur if the fabric is too tight or if children try to use a bow tie unattended. Made Recently View more 11 total. Add a photo Upload error. Tell us more about it? Click here to share your story. Bow Ties In other languages: Did this article help you?
Cookies make wikiHow better.
Put your finger on the tie where you envision the location of the bow tie's knot in the center of the rectangle. Pinch the long side of the tie and create a concave arch with the material, creating a crease along the seam on the underside of the tie. The next loop creates the center knot of the bow tie. The bow tie is a descendant of the knotted cravat. It was born from the need for neckwear that was easier to wear than the cravat and that would last throughout a more active day. By the end of the 19th century, the butterfly and batwing bow tie were commonplace. Oct 29, · You want this to look as close to a bow tie as possible, in order to give it those two extra back flaps you need to fold it two more times. To do this simply put your hand over the fold you already made and fold over .